Nie masz w koszyku żadnych produktów
 
English Polski Spanish 
Szukaj instrukcji do
 

(e.g. AA-V20EG JVC, ZX-7 Sony )
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Kto jest w sklepie?
Sklep przegląda 5934 gości i 
1 zarejestrowany klient 
Kategorie
Informacje
Polecamy
Strona główna >> HUSQVARNA >> RIDER13HBIO Instrukcja Obsługi
 
 0 szt. w koszyku 

HUSQVARNA RIDER13HBIO
Instrukcja Obsługi


Tweetnij o tym produkcie a dostaniesz $1.00 rabatu!
  • Plik do pobrania
  • Format PDF
  • Kompletna instrukcja
  • Język: English
Cena: $4.99

Opis HUSQVARNA RIDER13HBIO Instrukcja Obsługi

Kompletna instrukcja obsługi w formie pliku PDF. Plik PDF zostanie dostarczony na Twój adres email po jego zakupieniu.

Instrukcje obsługi (czasami nazywane także podręcznikiem użytkownika) opisuja funkcje i sposób działania danego produktu.

Instrukcja jest dostępna w następujących językach: English

Plik nie jest jeszcze gotowy
Musisz najpierw dokonać zakupu.

Recenzje produktu
Dla tego produktu nie napisano jeszcze recenzji!

Tekstowy podgląd strony 31 (kliknij aby zobaczyć)
MAINTENANCE
Adjustment of the cutting unit�s parallelism for the Rider 11 Bio and Rider 13 Bio
1. Check the tyre air pressure. It should be 60 kPa (0,6 kp/cm2). 2. Dismantle the front hood and right-hand fender as described on page 20-21. 3. Vertical adjustment of the cutting unit is made with the adjusting nuts on the back edge of the lift-strut. 4. Raise the cutting unit at the front edge by shortening the lift-strut. Lower the cutting unit at the front edge by lengthening the lift-strut. 5. Tighten the nuts against each other after the adjustment. 6. On completion of the adjustment the unit�s parallelism should be re-checked. Fit the right-hand fender and the front hood.

2

Adjusting the alignment of the cutting unit for the Rider 11 Bio and Rider 13 Bio
1. Check the tyre air pressure. It should be 60 kPa (0,6 kp/cm2). 2. Remove the front hood and right-hand fender as described on page 20-21. 3. Unscrew the nut (1) from the parallel strut. Remove the clip (2) and the parallel strut. 4. Turn the fork anti-clockwise to lower the rear edge of the hood, or clockwise to raise the rear edge of the hood. 5. Once adjustment is complete, refit the parallel strut and clip and tighten the nut. 6. Recheck the alignment of the cutting unit after adjustment. 7. Refit the right-hand fender and hood.

30 � English

Klienci kupując ten produkt kupili także

$4.99

SX-K700 TECHNICS
Instrukcja Obsługi

Kompletna instrukcja obsługi w formie pliku PDF. Plik PDF zostanie dostarczony na Twój adres email…

$4.99

CJ-V51 PIONEER
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…

$4.99

GRAND PRIX ELECTRONIC 754 BECKER
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…

$4.99

SX-PR602 TECHNICS
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…

$4.99

EV-S1000E SONY
Instrukcja Obsługi

Kompletna instrukcja obsługi w formie pliku PDF. Plik PDF zostanie dostarczony na Twój adres email…

$4.99

GRAND PRIX ELECTRONIC 780 BECKER
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…

$4.99

AG7330 PANASONIC
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…

$4.99

EVO-9850 VOLUME 1 SONY
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…
>
Parse Time: 0.226 - Number of Queries: 127 - Query Time: 0.049