Nie masz w koszyku żadnych produktów
 
English Polski Spanish 
Szukaj instrukcji do
 

(e.g. AA-V20EG JVC, ZX-7 Sony )
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Kto jest w sklepie?
Sklep przegląda 5249 gości 
Kategorie
Informacje
Polecamy
Strona główna >> HUSQVARNA >> RIDERPRO15 Instrukcja Obsługi
 
 0 szt. w koszyku 

HUSQVARNA RIDERPRO15
Instrukcja Obsługi


Tweetnij o tym produkcie a dostaniesz $1.00 rabatu!
  • Plik do pobrania
  • Format PDF
  • Kompletna instrukcja
  • Język: English
Cena: $4.99

Opis HUSQVARNA RIDERPRO15 Instrukcja Obsługi

Kompletna instrukcja obsługi w formie pliku PDF. Plik PDF zostanie dostarczony na Twój adres email po jego zakupieniu.

Instrukcje obsługi (czasami nazywane także podręcznikiem użytkownika) opisuja funkcje i sposób działania danego produktu.

Instrukcja jest dostępna w następujących językach: English

Plik nie jest jeszcze gotowy
Musisz najpierw dokonać zakupu.

Recenzje produktu
Dla tego produktu nie napisano jeszcze recenzji!

Tekstowy podgląd strony 47 (kliknij aby zobaczyć)
MAINTENANCE
Checking and Adjusting the Cutting Unit�s Ground Pressure
In order to achieve the best mowing result the cutting unit should follow the ground without touching it too heavily. The pressure is adjusted using a screw on each side of the Rider. 1. Check the air pressure in the tyres 60 kPa / 0.6 bar / 9 PSI. 2. Place the Rider on a flat surface. 3. Put the lifting lever in the mowing position. 4. Place a set of bathroom scales under the cutting unit�s frame (on the front edge) so that the unit rests on the scales. If necessary a block can be placed between the frame and the scales so that the anti-scalp rollers do not support any weight. 5. Adjust the cutting unit�s ground pressure by screwing the adjuster screws, which are located behind the front wheels on both sides, in or out. The ground pressure should be between 12 and 15 kg (26.5-33 lb). IMPORTANT INFORMATION When changing the cutting unit, you must readjust the parallelism and cutting height.

6017-216

8009-597

Cutting Height
1. Place the Rider on a flat surface. 2. Loosen the nut on the height adjustment strut. 3. Measure the distance between the ground and cutting unit�s edge at the front of the cover. The cutting unit should have a slight slant, with the rear edge 2-4 mm (1/8") higher than the front edge. The distance between the front edge and the ground should be: � 40 mm for Combi 94 and Combi 103 � 35 mm for Combi 112. 4. Tighten the nut. 5. Check that the parallelism has not changed. If so, the parallelism must be readjusted. 6. Check and if necessary adjust the cutting unit�s ground pressure. 7. Fit the front cover.
8009-028 8009-564

English �

45

Klienci kupując ten produkt kupili także

$4.99

SX-K700 TECHNICS
Instrukcja Obsługi

Kompletna instrukcja obsługi w formie pliku PDF. Plik PDF zostanie dostarczony na Twój adres email…

$4.99

CJ-V51 PIONEER
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…

$4.99

GRAND PRIX ELECTRONIC 754 BECKER
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…

$4.99

SX-PR602 TECHNICS
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…

$4.99

EV-S1000E SONY
Instrukcja Obsługi

Kompletna instrukcja obsługi w formie pliku PDF. Plik PDF zostanie dostarczony na Twój adres email…

$4.99

GRAND PRIX ELECTRONIC 780 BECKER
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…

$4.99

AG7330 PANASONIC
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…

$4.99

EVO-9850 VOLUME 1 SONY
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…
>
Parse Time: 0.17 - Number of Queries: 125 - Query Time: 0.043